SD-карта Samsung Evo Plus for Creators 32Gb и тестер для карт

/*
 * This program attempts to initialize an SD card and analyze its structure.
 */
#include "SdFat.h"
#include "sdios.h"
/*
  Set DISABLE_CS_PIN to disable a second SPI device.
  For example, with the Ethernet shield, set DISABLE_CS_PIN
  to 10 to disable the Ethernet controller.
*/
const int8_t DISABLE_CS_PIN = -1;
/*
  Change the value of SD_CS_PIN if you are using SPI
  and your hardware does not use the default value, SS.
  Common values are:
  Arduino Ethernet shield: pin 4
  Sparkfun SD shield: pin 8
  Adafruit SD shields and modules: pin 10
*/
// SDCARD_SS_PIN is defined for the built-in SD on some boards.
#ifndef SDCARD_SS_PIN
const uint8_t SD_CS_PIN = SS;
#else  // SDCARD_SS_PIN
const uint8_t SD_CS_PIN = SDCARD_SS_PIN;
#endif  // SDCARD_SS_PIN

// Try to select the best SD card configuration.
#if HAS_SDIO_CLASS
#define SD_CONFIG SdioConfig(FIFO_SDIO)
#elif ENABLE_DEDICATED_SPI
#define SD_CONFIG SdSpiConfig(SD_CS_PIN, DEDICATED_SPI, SD_SCK_MHZ(16))
#else  // HAS_SDIO_CLASS
#define SD_CONFIG SdSpiConfig(SD_CS_PIN, SHARED_SPI, SD_SCK_MHZ(16))
#endif  // HAS_SDIO_CLASS

//------------------------------------------------------------------------------
SdFs sd;
cid_t m_cid;
csd_t m_csd;
uint32_t m_eraseSize;
uint32_t m_ocr;
static ArduinoOutStream cout(Serial);
//------------------------------------------------------------------------------
bool cidDmp() {
  String ManufName = "Unknown";
  if (int(m_cid.mid)==0) ManufName = "Invalid";
  if (int(m_cid.mid)==1) ManufName = "Panasonic Corporation";
  if (int(m_cid.mid)==2) ManufName = "Toshiba Corporation";
  if (int(m_cid.mid)==3) ManufName = "Sandisk Corporation";
  if (int(m_cid.mid)==6) ManufName = "Ritek Corporation (EXP 2018)";
  if (int(m_cid.mid)==9) ManufName = "ATP Electronics Inc.";
  if (int(m_cid.mid)==19) ManufName = "Kingmax Semiconductor Inc.(EXP 2014)";
  if (int(m_cid.mid)==25) ManufName = "Dynacard Co., Ltd.";
  if (int(m_cid.mid)==26) ManufName = "Power Quotient Intl. Co., Ltd (EXP 2017)";
  if (int(m_cid.mid)==27) ManufName = "Samsung Electronics Co., Ltd.";
  if (int(m_cid.mid)==29) ManufName = "ADATA Technology Co., Ltd.(AData, Corsair)";
  if (int(m_cid.mid)==39) ManufName = "Phison Electronics Corp. (AgfaPhoto, Delkin, Integral, Lexar, Patriot, PNY, Polaroid, Sony, Verbatim";
  if (int(m_cid.mid)==40) ManufName = "Barun Electronics (EXP 2019) (Lexar, PNY, ProGrade)";
  if (int(m_cid.mid)==49) ManufName = "Silicon Power Computer & Comm., Inc. (EXP 2017)";
  if (int(m_cid.mid)==54) ManufName = "Crucial";
  if (int(m_cid.mid)==65) ManufName = "Kingston";
  if (int(m_cid.mid)==69) ManufName = "MIXZA";
  if (int(m_cid.mid)==81) ManufName = "STEC Inc. / SimpleTech (EXP 2010)";
  if (int(m_cid.mid)==93) ManufName = "SwissBit AG";
  if (int(m_cid.mid)==97) ManufName = "Netlist, Inc.";
  if (int(m_cid.mid)==99) ManufName = "Cactus Technologies";
  if (int(m_cid.mid)==115) ManufName = "Silicon Power?";
  if (int(m_cid.mid)==116) ManufName = "Jiaelec Corp.";
  if (int(m_cid.mid)==130) ManufName = "Jiang Tay Technical Co., Ltd.";
  if (int(m_cid.mid)==131) ManufName = "Netcom Technology (HK) Ltd. (EXP 2015)";
  if (int(m_cid.mid)==132) ManufName = "Strontium Technologies Pte Ltd (EXP 2019)";
  if (int(m_cid.mid)==156) ManufName = "LD, MIXZA 333x";
  if (int(m_cid.mid)==173) ManufName = "Shenzhen Longsys Electronics Co., Ltd (Lexar 2021)";

/*
  if (int(m_cid.mid)==0) ManufName = "AGI Technology Co., Ltd";
  if (int(m_cid.mid)==0) ManufName = "Biwin Storage Technology CO., LTD";
  if (int(m_cid.mid)==0) ManufName = "BUFFALO INC.";
  if (int(m_cid.mid)==0) ManufName = "Centon Electronics Inc.";
  if (int(m_cid.mid)==0) ManufName = "Delidor Digital Technology Co., Limited";
  if (int(m_cid.mid)==0) ManufName = "Delkin Devices";
  if (int(m_cid.mid)==0) ManufName = "DIGILINK ELECTRONIC LIMITED";
  if (int(m_cid.mid)==0) ManufName = "Edisk Technology Ltd.";
  if (int(m_cid.mid)==0) ManufName = "G. Skill International Enterprises";
  if (int(m_cid.mid)==0) ManufName = "Grand and Broad Technology Co. Limited";
  if (int(m_cid.mid)==0) ManufName = "GTS Co. Ltd";
  if (int(m_cid.mid)==0) ManufName = "Guangdong Transcend Semiconductor Co., Ltd.";
  if (int(m_cid.mid)==0) ManufName = "Hagiwara Solutions Co., Ltd.";
  if (int(m_cid.mid)==0) ManufName = "HOSIN Global Electronics Co., Limited";
  if (int(m_cid.mid)==0) ManufName = "Innodisk Corp.";
  if (int(m_cid.mid)==0) ManufName = "Integral Memory Plc";
  if (int(m_cid.mid)==0) ManufName = "Keple Ltd";
  if (int(m_cid.mid)==0) ManufName = "LEAPRO TECHNOLOGY CO., LTD.";
  if (int(m_cid.mid)==0) ManufName = "Metorage Semiconductor technology Co., Ltd";
  if (int(m_cid.mid)==0) ManufName = "REALTECH SEMICONDUCTOR TECHNOLOGY LIMITED";
  if (int(m_cid.mid)==0) ManufName = "SC Global Company Co., Ltd";
  if (int(m_cid.mid)==0) ManufName = "Shenzhen Dadongjia Industrial Co., Ltd.";
  if (int(m_cid.mid)==0) ManufName = "Shenzhen Shenghua Youxin Semiconductor Technology Limited";
  if (int(m_cid.mid)==0) ManufName = "Shenzhen YeKeSheng Digital Co.,Ltd.";
  if (int(m_cid.mid)==0) ManufName = "SMART Modular Technologies (Global), Inc.";
  if (int(m_cid.mid)==0) ManufName = "SPYRUS INC.";
  if (int(m_cid.mid)==0) ManufName = "Taishin International Resources Co., Ltd.";
  if (int(m_cid.mid)==0) ManufName = "Virtium LLC";
  if (int(m_cid.mid)==0) ManufName = "WETOP TECHNOLOGY CORPORATION LIMITED";
  if (int(m_cid.mid)==0) ManufName = "Wintec Industries, Inc.";
  if (int(m_cid.mid)==0) ManufName = "Yuanchuang Digital Technology Limited";
  
*/
  cout << F("\nManufacturer ID: ");
  cout << uppercase << showbase << hex << int(m_cid.mid) << dec << endl;
  cout << ManufName << endl;
  cout << F("OEM ID: ") << m_cid.oid[0] << m_cid.oid[1] << endl;
  cout << F("Product: ");
  for (uint8_t i = 0; i < 5; i++) {
    cout << m_cid.pnm[i];
  }
  cout << F("\nVersion: ");
  cout << int(m_cid.prv_n) << '.' << int(m_cid.prv_m) << endl;
  cout << F("Serial number: ") << hex << m_cid.psn << dec << endl;
  cout << F("Manufacturing date: ");
  cout << int(m_cid.mdt_month) << '/';
  cout << (2000 + m_cid.mdt_year_low + 16* m_cid.mdt_year_high) << endl;
  cout << endl;
  return true;
}
//------------------------------------------------------------------------------
void clearSerialInput() {
  uint32_t m = micros();
  do {
    if (Serial.read() >= 0) {
      m = micros();
    }
  } while (micros() - m < 10000);
}
//------------------------------------------------------------------------------
bool csdDmp() {
  bool eraseSingleBlock;
  if (m_csd.v1.csd_ver == 0) {
    eraseSingleBlock = m_csd.v1.erase_blk_en;
    m_eraseSize = (m_csd.v1.sector_size_high << 1) | m_csd.v1.sector_size_low;
  } else if (m_csd.v2.csd_ver == 1) {
    eraseSingleBlock = m_csd.v2.erase_blk_en;
    m_eraseSize = (m_csd.v2.sector_size_high << 1) | m_csd.v2.sector_size_low;
  } else {
    cout << F("m_csd version error\n");
    return false;
  }
  m_eraseSize++;
  cout << F("cardSize: ") << 0.000512 * sdCardCapacity(&m_csd);
  cout << F(" MB (MB = 1,000,000 bytes)\n");

  cout << F("flashEraseSize: ") << int(m_eraseSize) << F(" blocks\n");
  cout << F("eraseSingleBlock: ");
  if (eraseSingleBlock) {
    cout << F("true\n");
  } else {
    cout << F("false\n");
  }
  return true;
}
//------------------------------------------------------------------------------
void errorPrint() {
  if (sd.sdErrorCode()) {
    cout << F("SD errorCode: ") << hex << showbase;
    printSdErrorSymbol(&Serial, sd.sdErrorCode());
    cout << F(" = ") << int(sd.sdErrorCode()) << endl;
    cout << F("SD errorData = ") << int(sd.sdErrorData()) << endl;
  }
}
//------------------------------------------------------------------------------
bool mbrDmp() {
  MbrSector_t mbr;
  bool valid = true;
  if (!sd.card()->readSector(0, (uint8_t*)&mbr)) {
    cout << F("\nread MBR failed.\n");
    errorPrint();
    return false;
  }
  cout << F("\nSD Partition Table\n");
  cout << F("part,boot,bgnCHS[3],type,endCHS[3],start,length\n");
  for (uint8_t ip = 1; ip < 5; ip++) {
    MbrPart_t *pt = &mbr.part[ip - 1];
    if ((pt->boot != 0 && pt->boot != 0X80) ||
        getLe32(pt->relativeSectors) > sdCardCapacity(&m_csd)) {
      valid = false;
    }
    cout << int(ip) << ',' << uppercase << showbase << hex;
    cout << int(pt->boot) << ',';
    for (int i = 0; i < 3; i++ ) {
      cout << int(pt->beginCHS[i]) << ',';
    }
    cout << int(pt->type) << ',';
    for (int i = 0; i < 3; i++ ) {
      cout << int(pt->endCHS[i]) << ',';
    }
    cout << dec << getLe32(pt->relativeSectors) << ',';
    cout << getLe32(pt->totalSectors) << endl;
  }
  if (!valid) {
    cout << F("\nMBR not valid, assuming Super Floppy format.\n");
  }
  return true;
}
//------------------------------------------------------------------------------
void dmpVol() {
  cout << F("\nScanning FAT, please wait.\n");
  uint32_t freeClusterCount = sd.freeClusterCount();
  if (sd.fatType() <= 32) {
    cout << F("\nVolume is FAT") << int(sd.fatType()) << endl;
  } else {
    cout << F("\nVolume is exFAT\n");
  }
  cout << F("sectorsPerCluster: ") << sd.sectorsPerCluster() << endl;
  cout << F("clusterCount:      ") << sd.clusterCount() << endl;
  cout << F("freeClusterCount:  ") << freeClusterCount << endl;
  cout << F("fatStartSector:    ") << sd.fatStartSector() << endl;
  cout << F("dataStartSector:   ") << sd.dataStartSector() << endl;
  if (sd.dataStartSector() % m_eraseSize) {
    cout << F("Data area is not aligned on flash erase boundary!\n");
    cout << F("Download and use formatter from www.sdcard.org!\n");
  }
}
//------------------------------------------------------------------------------
void printCardType() {

  cout << F("\nCard type: ");

  switch (sd.card()->type()) {
    case SD_CARD_TYPE_SD1:
      cout << F("SD1\n");
      break;

    case SD_CARD_TYPE_SD2:
      cout << F("SD2\n");
      break;

    case SD_CARD_TYPE_SDHC:
      if (sdCardCapacity(&m_csd) < 70000000) {
        cout << F("SDHC\n");
      } else {
        cout << F("SDXC\n");
      }
      break;

    default:
      cout << F("Unknown\n");
  }
}
//------------------------------------------------------------------------------
void printConfig(SdSpiConfig config) {
  if (DISABLE_CS_PIN < 0) {
    cout << F(
           "\nAssuming the SD is the only SPI device.\n"
           "Edit DISABLE_CS_PIN to disable an SPI device.\n");
  } else {
    cout << F("\nDisabling SPI device on pin ");
    cout << int(DISABLE_CS_PIN) << endl;
    pinMode(DISABLE_CS_PIN, OUTPUT);
    digitalWrite(DISABLE_CS_PIN, HIGH);
  }
  cout << F("\nAssuming the SD chip select pin is: ") << int(config.csPin);
  cout << F("\nEdit SD_CS_PIN to change the SD chip select pin.\n");
}
//------------------------------------------------------------------------------
void printConfig(SdioConfig config) {
  (void)config;
  cout << F("Assuming an SDIO interface.\n");
}
//-----------------------------------------------------------------------------
void setup() {
  Serial.begin(9600);
  // Wait for USB Serial
  while (!Serial) {
    SysCall::yield();
  }
  cout << F("SdFat version: ") << SD_FAT_VERSION_STR << endl;
  printConfig(SD_CONFIG);

}
//------------------------------------------------------------------------------
void loop() {
  // Read any existing Serial data.
  clearSerialInput();

  // F stores strings in flash to save RAM
  cout << F("\ntype any character to start\n");
  while (!Serial.available()) {
    SysCall::yield();
  }
  uint32_t t = millis();
  if (!sd.cardBegin(SD_CONFIG)) {
    cout << F(
           "\nSD initialization failed.\n"
           "Do not reformat the card!\n"
           "Is the card correctly inserted?\n"
           "Is there a wiring/soldering problem?\n");
    if (isSpi(SD_CONFIG)) {
      cout << F(
           "Is SD_CS_PIN set to the correct value?\n"
           "Does another SPI device need to be disabled?\n"
           );
    }
    errorPrint();
    return;
  }
  t = millis() - t;
  cout << F("init time: ") << t << " ms" << endl;

  if (!sd.card()->readCID(&m_cid) ||
      !sd.card()->readCSD(&m_csd) ||
      !sd.card()->readOCR(&m_ocr)) {
    cout << F("readInfo failed\n");
    errorPrint();
    return;
  }
  printCardType();
  cidDmp();
  csdDmp();
  cout << F("\nOCR: ") << uppercase << showbase;
  cout << hex << m_ocr << dec << endl;
  if (!mbrDmp()) {
    return;
  }
  if (!sd.volumeBegin()) {
    cout << F("\nvolumeBegin failed. Is the card formatted?\n");
    errorPrint();
    return;
  }
  dmpVol();
}

Card type: SDXC

Manufacturer ID: 0X82
Jiang Tay Technical Co., Ltd.
OEM ID: JT
Product: NCard
Version: 0.2
Serial number: 0X37D800B1
Manufacturing date: 10/2014

cardSize: 63416.83 MB (MB = 1,000,000 bytes)
flashEraseSize: 128 blocks
eraseSingleBlock: true

OCR: 0XC0FF8000

SD Partition Table
part,boot,bgnCHS[3],type,endCHS[3],start,length
1,0X0,0XA,0X9,0X2,0X7,0XFE,0XFF,0XFF,32768,123828224
2,0X0,0X0,0X0,0X0,0X0,0X0,0X0,0X0,0,0
3,0X0,0X0,0X0,0X0,0X0,0X0,0X0,0X0,0,0
4,0X0,0X0,0X0,0X0,0X0,0X0,0X0,0X0,0,0

volumeBegin failed. Is the card formatted?
SD errorCode: SD_CARD_ERROR_INVALID_CARD_CONFIG = 0X2A
SD errorData = 0X0